Second Skin Audio Damplifier Pro 36.5 sqft 80 Mil Automotive Sound Deadening Mat

Description

***This box ships free to the lower 48 states, this box does not ship free to Hawaii, Alaska, or any U.S. territories. We offer 4 other options for free shipping to these locations. ***
Damplifier Pro - CLD Sound Deadener & Vibration Damper * MADE IN THE USA *
36.5
sq ft
Damplifier Pro (12" x 20") sheet sizes. Simply cut, peel & stick to any sheet metal, fiberglass or carbon fiber.
Foil - Annealed black foil with ghosted logo
Damplifier Pro uses an ultra-thick 6.5 mil black annealed foil. Thicker foil means better sound deadening, vibration control, heat dissipation and easier installation with less risk of tearing.
Butyl Rubber Adhesive - High Quality USA made
High temperature butyl adhesive with increased elastomeric properties. Less fillers and more rubber means better vibration damping and noise reduction. 450 degree F thermal rating, Damplifier Pro will not melt, out gas, or fall off.
The quality of the the butyl rubber and thickness of the foil create the overall effectiveness of any C.L.D.
Most noise problems in a vehicle are caused by vibrations from the structure. Typically created by, road/tires, engine, and base stereos systems. This causes the surfaces, such as the floor, ceiling, and doors, to emit a drone sound like a cymbal on a drum set or a bell ringing. Damplifier Pro uses 2 mm, 100% American-made, heat-resistant butyl rubber layer to absorb this vibrations energy, then slowly dissipates it through a 6.5 mil Annealed aluminum foil layer preventing this from becoming noise.
WHY WOULD I NEED TO ADD A SOUND DEADENER TO MY VEHICLE? Cars are made of metal. Metal rattles and shakes to create structural noise. Luxury cars come loaded with sound deadening materials to create a quiet, calm car environment. If you’re restoring on old vehicle, installing expensive car audio, or just have a vehicle that makes a lot of road noise, adding extra automotive sound insulation will allow you to hear the quality notes of your new sound system.
WHAT MAKES A GOOD SOUND DAMPENER? You’re looking for high quality butyl rubber and a thick foil constraint layer. More butyl rubber and less fillers means better vibration damping and noise control. A thick foil layer improves sound deadening properties and also helps with thermal insulation.
HOW CAN I TELL IF I’VE GOT THE GOOD STUFF? Most asphalt products won’t just come out and say it. It’s bad for business. You have to sniff it out. The easiest ways to tell are the thermal heat rating (if it’s not listed or below 300 F, you don’t have much rubber) and the price the square foot. Butyl rubber is expensive. You should be skeptical if the price gets too low. At Second Skin, we love bringing you a high quality product at the best VALUE in the industry.
DAMPLIFIER PRO™ IS ENGINEERED FOR PERFORMANCE. With an industry leading heat rating of 450 F and a proprietary combination of American made butyl rubber and annealed foil, Damplifier Pro™ sound deadening sheets kill vibration noise, stop echos, and increases the strength and resilience of the car’s metal, all while meeting high health safety standards (RoHS compliant). Just cut, peel, and stick to any prepared fiberglass, aluminum, or sheet metal.
Proudly made in the USA and endorsed by Chad Utt, WEST COAST CUSTOMS operations manager: “I am blown away by how quiet and dead the sheet metal is. I would have to layer up competitor products three, four, sometimes five layers thick to achieve the same results. Awesome stuff man!!!!!”
Second Skin offers a 100% quality guarantee. We are confident that our products will work exactly as advertised when installed correctly. The liability of Second Skin is limited only to replacement of defective material.
2 mm thick (80 mils) +/- 10%
.6 lbs. per square foot +/- 10%
Sheet size - 12" X 20" = 1.67 sq ft
Thermal range -75°F(-60°C) to 450°F(232°C)
meets ROHS compliance standards which is an EU standard restricting the use of 10 hazardous substances.
MADE IN THE USA - 300% more efficient than tar boards and asphalt mats.
·
The quality of the the butyl rubber and thickness of the foil create the overall effectiveness of any sound deadener. Roofing products are frequently labeled as sound insulation. However they are typically made overseas from inexpensive alternatives to butyl rubber such as asphalt, tar, or bitumen with very thin foil or Mylar. Although less expensive, they are much lower quality, will not perform well, and may out-gas harmful vapors and/or melt and fall off.
·
The true performance of Damplifier Pro comes from details you cannot see, such as the unique chemistry of the high performance US made butyl rubber. Damplifier Pro is made of 2 mm thick elastomeric butyl rubber with a 6.5 mil black annealed foil constraint layer. The thermal range is -75°F(-60°C) to 450°F(232°C). and will not melt, out-gas or fall off. Damplifier Pro is ROHS compliant, an EU standard restricting the use of 10 hazardous substances.
·
CHAD UTT, WEST COAST CUSTOMS OPERATIONS MANAGER: “We skinned the entire vehicle floor, walls, doors, and roof with Second Skin Damplifier Pro and the Luxury Foam padding. I am blown away by how quiet and dead the sheet metal is. I would have to layer up competitor product three, four, sometimes five layers thick to achieve the same results. Awesome stuff man!!!!! Really, REALLY, happy with the product!!! “